OOOOOOOOOOO
2004 Bobcat T250 Rubber Track Skid Steer Loader
Price: $19,500
This 2004 Bobcat T250 is powered by a Kubota 81 HP Turbo diesel engine. The engine always starts instantly, runs quietly without excessive smoke or blow by. There are no strange or odd noises from the engine. The engine is dry, has no signs of leaks. The sheet metal is very straight, including the back door and engine side and top panels. The back door opens and shuts well with a good latch. There is a small dent in the bottom of the back door. The front of the machine is straight, the paint shows normal wear on the front of the loader arms, track frames, lower frames and back door. The ROPS is also very straight and has original paint. The paint on the back door and fronts of the loader arms has been touched up, the decal for the back door is on order. The quick attach plate pins and bushings are tight. The low profile bucket is in good condition with good bolt on cutting edge. The bucket bottom is good, no holes or damage. The seat is good, see the pictures. The interior controls (Standard Bobcat style controls, not switchable) work normally. The Open cab has a ceiling glass and a back window. The parking brake is good. There are auxiliary hydraulics, not high flow. The underside of the machine is dry with no signs of trouble, see the photo. The undercarriage is good, however the tracks are not matching, see the pictures. The Tracks are approximately 50% remaining. One sprocket is new the other one is 80% to 90% remaining, the roller bearings are good some of the rollers are getting thin. The drives are normal, quiet and neutral is dead center with no creep. This machine really does run well, I believe the hour meter. I have run it myself and it is very responsive and tight. This is not an auction piece, it did not come from an auction and it was not green and repainted. There are no cracks or welds. This machine is in very nice condition and it does not look abused.
Click Here To View More Images
This 2004 Bobcat T250 is powered by a Kubota 81 HP Turbo diesel engine. The engine always starts instantly, runs quietly without excessive smoke or blow by. There are no strange or odd noises from the engine. The engine is dry, has no signs of leaks. The sheet metal is very straight, including the back door and engine side and top panels. The back door opens and shuts well with a good latch. There is a small dent in the bottom of the back door. The front of the machine is straight, the paint shows normal wear on the front of the loader arms, track frames, lower frames and back door. The ROPS is also very straight and has original paint. The paint on the back door and fronts of the loader arms has been touched up, the decal for the back door is on order. The quick attach plate pins and bushings are tight. The low profile bucket is in good condition with good bolt on cutting edge. The bucket bottom is good, no holes or damage. The seat is good, see the pictures. The interior controls (Standard Bobcat style controls, not switchable) work normally. The Open cab has a ceiling glass and a back window. The parking brake is good. There are auxiliary hydraulics, not high flow. The underside of the machine is dry with no signs of trouble, see the photo. The undercarriage is good, however the tracks are not matching, see the pictures. The Tracks are approximately 50% remaining. One sprocket is new the other one is 80% to 90% remaining, the roller bearings are good some of the rollers are getting thin. The drives are normal, quiet and neutral is dead center with no creep. This machine really does run well, I believe the hour meter. I have run it myself and it is very responsive and tight. This is not an auction piece, it did not come from an auction and it was not green and repainted. There are no cracks or welds. This machine is in very nice condition and it does not look abused.
Click Here To View More Images
2003 JCB 190 Robot (JCB2003190)
Price: $13,900.00 Description:
This JCB 190 skid steer loader has only 778 hours, it is tight and runs great. This machine has joystick pilot controls similar to Cat. The sheet metal is very good with no damage and typical paint scratches on the rear corners and back door. The paint is original. The bucket is a 72" low profile with a fair cutting edge, it does not have a bolt on edge. The bucket pins and bushings are tight as are the loader cylinders, the cylinders are dry. 3 of the tires are very good, 1 tire should be replaced. The door works well. The JCB design is that you enter and exit through the left side of the machine, you can leave the loader up and in any position and still exit the machine without climbing over the loader, visibility is excellent.
Hours: 778
Make:
JCB Model: 190 Robot
Year: 2003
Horse Power: 57
Engine: 4 cylinder Perkins
Operating Load: 1985
Operating Weight: 7717 lbs
Click Here To View More Images
This JCB 190 skid steer loader has only 778 hours, it is tight and runs great. This machine has joystick pilot controls similar to Cat. The sheet metal is very good with no damage and typical paint scratches on the rear corners and back door. The paint is original. The bucket is a 72" low profile with a fair cutting edge, it does not have a bolt on edge. The bucket pins and bushings are tight as are the loader cylinders, the cylinders are dry. 3 of the tires are very good, 1 tire should be replaced. The door works well. The JCB design is that you enter and exit through the left side of the machine, you can leave the loader up and in any position and still exit the machine without climbing over the loader, visibility is excellent.
Hours: 778
Make:
JCB Model: 190 Robot
Year: 2003
Horse Power: 57
Engine: 4 cylinder Perkins
Operating Load: 1985
Operating Weight: 7717 lbs
Click Here To View More Images
JCB 8032 Mini Excavator
Price: $17,750 Hours: 700
This 2005 JCB Mini excavator is powered by a 27 HP Perkins Diesel engine that doesn't smoke or have blow-by. The engine starts instantly with normal operation . The engine is dry and quiet. The hydraulic pumps are dry and quiet as well. The Pilot Controls work well and are set up with the boom and swing on the right handle, dipper and bucket on the left handle, they are switch-able between backhoe style and Excavator style. Boom swing separate from house swing is controlled from the switch on the left handle. The sheet metal is straight with only very minor scratches, typical paint scrapes on the rear counterweight and track frames, there is one cracks in the cover over the hydraulic valve bank, see the picture. The paint is original and good. The seat is very good, the operator area is straight and neat. The ROPS is straight. There are no welds on the Boom or dipper or ROPS. The blade will lift the machine off the ground, the blade face is good and the cutting edge is good. The tracks are very good, approximately 80 to 90% remaining, with good tread depth. The Sprockets are good, approximately 80% remaining. I didn't hear any bad bearings while traveling, the 2 speed does work well. The underside of the machine is basically dry with no signs of trouble. The turntable bearing is tight, and not leaking grease, the swing break and boom swing both work normally and quietly. The king post bushings and pins are secure with no obvious wear. The bucket pins and bushings are tight. The digging bucket looks good, has minor denting in the bottom, the teeth are good. This machine has 706 hours, it runs and operates very well, it is a solid tight machine, I feel it will be a reliable machine. Remember, I can recheck any part for you, take more pictures if it helps you to make a decision about this machine.
Click Here To View More Images
This 2005 JCB Mini excavator is powered by a 27 HP Perkins Diesel engine that doesn't smoke or have blow-by. The engine starts instantly with normal operation . The engine is dry and quiet. The hydraulic pumps are dry and quiet as well. The Pilot Controls work well and are set up with the boom and swing on the right handle, dipper and bucket on the left handle, they are switch-able between backhoe style and Excavator style. Boom swing separate from house swing is controlled from the switch on the left handle. The sheet metal is straight with only very minor scratches, typical paint scrapes on the rear counterweight and track frames, there is one cracks in the cover over the hydraulic valve bank, see the picture. The paint is original and good. The seat is very good, the operator area is straight and neat. The ROPS is straight. There are no welds on the Boom or dipper or ROPS. The blade will lift the machine off the ground, the blade face is good and the cutting edge is good. The tracks are very good, approximately 80 to 90% remaining, with good tread depth. The Sprockets are good, approximately 80% remaining. I didn't hear any bad bearings while traveling, the 2 speed does work well. The underside of the machine is basically dry with no signs of trouble. The turntable bearing is tight, and not leaking grease, the swing break and boom swing both work normally and quietly. The king post bushings and pins are secure with no obvious wear. The bucket pins and bushings are tight. The digging bucket looks good, has minor denting in the bottom, the teeth are good. This machine has 706 hours, it runs and operates very well, it is a solid tight machine, I feel it will be a reliable machine. Remember, I can recheck any part for you, take more pictures if it helps you to make a decision about this machine.
Click Here To View More Images
1982 Case 580 Loader backhoe
Price: $10,250
I have moved this machine to a yard in Baltimore where it can be easily loaded into a container.
I purchased this machine from the original owner! The hour meter reads 3852 hours but had recently quit working. The machine is equipped with additional hydraulic plumbing to the rear for a hammer circuit. The glass is all intact, the cab is not rusty but the seat needs a new cover. The engine (Cummins 4.390) operates normally and has no signs of needing repair, the transmission and brakes work well as does the hydraulics, the parking brake does work. The tires are all very good, the body is not rusty and the paint is original. Call or email for additional pictures or details.
Click Here To View More Images
I have moved this machine to a yard in Baltimore where it can be easily loaded into a container.
I purchased this machine from the original owner! The hour meter reads 3852 hours but had recently quit working. The machine is equipped with additional hydraulic plumbing to the rear for a hammer circuit. The glass is all intact, the cab is not rusty but the seat needs a new cover. The engine (Cummins 4.390) operates normally and has no signs of needing repair, the transmission and brakes work well as does the hydraulics, the parking brake does work. The tires are all very good, the body is not rusty and the paint is original. Call or email for additional pictures or details.
Click Here To View More Images
2002 Takeuchi TB135 Mini Excavator
Price: $14,900
This 2002 Takeuchi mini excavator is powered by a 27 HP Yanmar Diesel engine that doesn't smoke or have blow-by. The engine starts instantly with normal operation . The engine is dry and quiet. The hydraulic pumps are dry and quiet as well. The engine oil was recently serviced. The Pilot Controls work well and are not sloppy, some of the push button controls are missing from the handles. The controls are switchable between Backhoe style and Excavator style. Boom swing is controlled by a foot pedal. The sheet metal is straight with only very minor scratches, typical paint scrapes on the rear counterweight and track frames. The paint is original and good. The seat is good but the seat cushion cover is worn out and should be recovered, the operator area is straight but needs a good cleaning. The Cab is straight. The glass is intact but I forgot to check the heat, there is no a/c. There are no welds on the Boom or dipper or ROPS. There is a thumb mounting plate welded to the dipper, there is not a thumb with the machine. The blade face is good and the cutting edge is good. The tracks are good, approximately 40 to 50% remaining, with good tread depth. The Sprockets are good, approximately 60% remaining. I didn't hear any bad bearings while traveling, the 2 speed does work well. The underside of the machine is basically dry with no signs of trouble. The turntable bearing is tight, and not leaking grease, the swing break and boom swing both work normally and quietly. The king post bushings and pins are secure with no obvious wear. There are some belly pans missing. The digging bucket looks good, the teeth are good but have a cutting edge welded to them for grading. the bucket has some play in the quick attach. The bucket and dipper cylinders are dry the boom cylinder is leaking. This machine has 2385 hours, it runs and operates very well, it is a solid tight machine, I feel it will be a reliable machine.
Remember, I can recheck any part for you, take more pictures if it helps you to make a decision about this machine.
Click Here To View More Images
This 2002 Takeuchi mini excavator is powered by a 27 HP Yanmar Diesel engine that doesn't smoke or have blow-by. The engine starts instantly with normal operation . The engine is dry and quiet. The hydraulic pumps are dry and quiet as well. The engine oil was recently serviced. The Pilot Controls work well and are not sloppy, some of the push button controls are missing from the handles. The controls are switchable between Backhoe style and Excavator style. Boom swing is controlled by a foot pedal. The sheet metal is straight with only very minor scratches, typical paint scrapes on the rear counterweight and track frames. The paint is original and good. The seat is good but the seat cushion cover is worn out and should be recovered, the operator area is straight but needs a good cleaning. The Cab is straight. The glass is intact but I forgot to check the heat, there is no a/c. There are no welds on the Boom or dipper or ROPS. There is a thumb mounting plate welded to the dipper, there is not a thumb with the machine. The blade face is good and the cutting edge is good. The tracks are good, approximately 40 to 50% remaining, with good tread depth. The Sprockets are good, approximately 60% remaining. I didn't hear any bad bearings while traveling, the 2 speed does work well. The underside of the machine is basically dry with no signs of trouble. The turntable bearing is tight, and not leaking grease, the swing break and boom swing both work normally and quietly. The king post bushings and pins are secure with no obvious wear. There are some belly pans missing. The digging bucket looks good, the teeth are good but have a cutting edge welded to them for grading. the bucket has some play in the quick attach. The bucket and dipper cylinders are dry the boom cylinder is leaking. This machine has 2385 hours, it runs and operates very well, it is a solid tight machine, I feel it will be a reliable machine.
Remember, I can recheck any part for you, take more pictures if it helps you to make a decision about this machine.
Click Here To View More Images